24 Cores Splitter Fiber Closure 4 IN 4 OUT Mechanical Splicing
The product provide with 8 fiber cable in-out round ports and the
cable diameter is from Ф10-Ф22. It can be used in aerial, duct and
direct buried application. This product is made from the
high-quality and with the mechanical sealing structure filled with
the sealing material. The external component and fastening piece
are all made from the high-quality stainless steel. It can be
opened after sealing.
Applications
● Telecommunication subscriber loop
● Fiber to the home(FTTH)
● LAN/WAN
Specification
| Item | Parameter |
| Type | SPFC-PH-XXM-4/4E |
| External Size | 470(L)× 240(W) × 120 (H) mm |
| Net weight | 3.5kg |
| Cable ports | four cable entry port on each end |
| Way to install | Aerial, duct and buried applications |
| Cable diameter | ∅10-∅22 |
| Capacity of splice tray | 24 single fiber |
| Max Capacity of Splice Tray | 8 |
| PLC Splitter Capacity | Optional support 1:32/2:16 Max type E |
| Sealing structure | Sticky cincture |
| Work Temperature | -40°C ~+70 °C |
| Optical fiber winding radius | ≥40mm |
| Extra loss of fiber tray | ≤ 0.01dB |
| Fiber length left in tray | ≥1.6m |
| Max Capacity | Fiber capacity: single:36cores |
| Lateral pressure-resistance | ≥2000N / 10cm |
| Shock-resistance | ≥20N.m |
Operations
● Choose the cable loop with proper outer diameter and let it go
through the optical cable. Peel the cable , take off the outer and
inner housing, as well as loose contract tube, and wash off the
filling grease, leaving 1.1~1.6mfiber and 30~50mm steel core.
● Fix the cable pressing card and cable, together with cable
reinforce steel core. If the diameter of the cable is less than
10mm, first bind the cable fixing point with adhesive tape till the
diameter has reached 12mm, then fix it.
● Lead the fiber into the melting and connecting tray, fix heat
contract tube and heat melt tube to one of the connecting fiber.
After melting and connecting the fiber, move heat contract tube and
heat melt tube and fix the stainless (or quartz)reinforce core
stick ,make sure the connecting point is in the middle of the
housing pipe. Heat the pipe to make the two into one. Put the
protected joint into the fiber-laying tray.(one tray can lay 12
cores)
● Lay the left fiber in the melting and connecting tray evenly, and
fix the winding fiber with nylon ties. Use the trays from the
bottom up. After all the fiber has been connected, cover the top
layer and fix it.
● Position it and use the earth wire in accordance with the project
plan.
● Sealing the cable retainer nearing the inlet of splice closure and
the joint of the cable rings with sealing tape. And close the
unused inlets with plugs, with exposed concave parts of the plug
sealed with tapes. Then put sealing trips into the sealing groove
on the sides of the shell and grease the concave part of inlet of
the body between the two parts of the shell. Then close the two
parts of the shell and tighten it with stainless steel bolts. The
bolts should be screwed tightly with balanced force. according to the laying requirement, position and fix the hanging
tool .
Ordering Information
| Model | Description | Size(mm) | Package | Weight/carton |
| SPFC-PH-24M-4/4E | Fiber Closure Horizontal type support Splitter 24 Cores Max , 24
Cores Splice Tray 4 IN 4 OUT Mechanical Splicing without
Splitter,support 1:16/1:8(2PCS) Max type E | 470*240*120 | 500*510*58/8PCS |
28.5KG/8PCS
|
| SPFC-PH-36M-4/4E | Fiber Closure Horizontal type support Splitter 36 Cores Max , 24
Cores Splice Tray 4 IN 4 OUT Mechanical Splicing without
Splitter,support 1:32/1:16(2PCS) Max type E |
| SPFC-PH-48M-4/4E | Fiber Closure Horizontal type support Splitter 48cores(24 duplex SC
adapters can be installed) 24 Cores Splice Tray 4 IN 4 OUT
Mechanical Splicing without Splitter,support 1:32/1:16(2PCS) Max
type E |
